centrifugal pump startup and shutdown procedure|pump shutdown procedure : ODM Nov 28, 2018 · Our team of experts got together this practical checklist for the startup and shutdown of a centrifugal pump. Dryer Industrial Thailand | ผู้ติดตาม 133 คนบน LinkedIn Sustainable air & water solutions for industrial applications | Established since 1998 in Thailand, Chonburi Province, we became .
{plog:ftitle_list}
IDEC High-G drying shaker is designed to meet the demand of drilling waste management and environmental request. It is a kind of shale shaker with high G force. Usually be used to dry the drilling cuttings generated from primary solids control equipment including shale shakers, mud cleaner, desander and desilter.
Centrifugal pumps are widely used in various industries for transferring fluids. Proper startup and shutdown procedures are crucial to ensure the efficient and safe operation of centrifugal pumps. In this article, we will discuss the step-by-step process for starting up and shutting down a centrifugal pump.
Our team of experts got together this practical checklist for the startup and shutdown of a centrifugal pump.
Centrifugal Pump Startup Procedure
1. **Check Pipework and Equipment**: Before starting the centrifugal pump, it is essential to inspect all pipework and associated equipment to ensure they are clean and free from debris. Make sure that pipe connections are secure and leak-free to prevent any potential issues during operation.
2. **Check Pump Installation**: Inspect the pump installation to ensure it is properly aligned and supported. Check for any signs of misalignment or vibration that could indicate potential problems.
3. **Prime the Pump**: If the centrifugal pump is not self-priming, ensure that the pump is properly primed before starting. This will help prevent damage to the pump and ensure efficient operation.
4. **Open Inlet Valve**: Slowly open the inlet valve of the pump to allow the fluid to flow into the pump casing. This will help create the necessary suction for the pump to start working.
5. **Start the Pump**: Once the pump is primed and the inlet valve is open, start the pump motor. Monitor the pump for any unusual noises or vibrations that could indicate issues with the pump operation.
6. **Adjust Flow Rate**: Gradually increase the flow rate of the pump to the desired level. Avoid sudden changes in flow rate, as this can cause water hammer and damage the pump.
7. **Monitor Operation**: Keep an eye on the pump operation, including pressure, flow rate, and motor temperature. Make adjustments as needed to ensure optimal performance.
Centrifugal Pump Shutdown Procedure
1. **Reduce Flow Rate**: Before shutting down the centrifugal pump, reduce the flow rate gradually to allow the pump to adjust to lower operating conditions.
2. **Close Inlet Valve**: Once the flow rate has been reduced, close the inlet valve of the pump to stop the flow of fluid into the pump casing.
3. **Stop the Pump**: Turn off the pump motor to stop the pump operation. Allow the pump to come to a complete stop before proceeding with further shutdown steps.
4. **Check Pressure**: After the pump has stopped, check the pressure gauge to ensure that there is no residual pressure in the system. Release any trapped pressure before proceeding.
5. **Vent the Pump**: Open the pump casing or discharge valve to vent any remaining fluid from the pump. This will help prevent damage to the pump seals and bearings.
6. **Inspect for Leaks**: Once the pump has been vented, inspect the pump and surrounding pipework for any signs of leaks. Repair any leaks before restarting the pump.
Centrifugal pump start-up in reverse rotation can result in the contact of metal parts, heat generation, and breach of containment. Flush and clean the system thoroughly to remove dirt or debris in the pipe system in order to prevent …
Stockpiled drilling muds are transferred to the 1 feed hopper mounted on the 2 live bottom feeder of the Primary Treatment Unit (PTU) by a backhoe or skid loader. From the live bottom feeder, .In 2015 SAR established a plant for treatment of OBM Drill Cuttings for Kuwait Oil Company (KOC) in North Kuwait. The plant has been in operation since July 2015 and uses Indirect .
centrifugal pump startup and shutdown procedure|pump shutdown procedure