centrifugal pump suction and discharge|centrifugal pump selection chart : importers Include five to 10 pipe diameters of straight-run pipe between the pump inlet and elbow. This helps to eliminate the “side loading” of the pump impeller and creates uniform pump axial bearing loading. See more Flexible Screw Conveyor Installation and Operation Manual - 10 - FLEXICON CORPORATION 2400 Emrick Boulevard Bethlehem, PA 18020-8006 USA Tel: 1-888-FLEXICON Tel: 1-610-814-2400 Fax: 1-610-814-0600 www.flexicon.com
{plog:ftitle_list}
Metalfab Convey-All/FSC Flexible Screw Conveyors feature a rugged modular design and provide a highly effective yet economical means to convey powder or granular material without product separation. Conveyors are available in configurations from 10 to 20 ft. lengths with a choice of a 3˝ diameter helix screw rated to convey up to 150 cu. ft .
Centrifugal pumps are widely used in various industries for transferring fluids from one location to another. Proper installation of centrifugal pump suction and discharge piping is crucial for the efficient operation of the pump. In this article, we will discuss the importance of using eccentric reducers on the suction side of the pump when a pipe size transition is required and best practices for pump discharge piping.
Include a straight-run pipe length equal to five to 10 times the pipe diameter between the pump inlet and any obstruction in the suction line. Obstructions include valves, elbows, “tees,” etc. Keeping the pump suction piping short ensures that the inlet pressure drop is as low as possible. The straight-run pipe gives
Centrifugal Pump Suction Side
When a pipe size transition is needed on the suction side of a centrifugal pump, it is recommended to use eccentric reducers. Eccentric reducers are designed to maintain a smooth flow of fluid by gradually reducing the pipe size without causing turbulence or cavitation in the pump.
It is important to install the eccentric reducer with the flat side on the top. This orientation helps prevent air pockets from forming in the suction line, which can lead to pump cavitation and reduce the pump's efficiency. By ensuring proper alignment of the eccentric reducer, you can improve the overall performance and longevity of the centrifugal pump.
Centrifugal Pump Discharge Side
Proper installation of the discharge piping is essential to ensure the efficient operation of the centrifugal pump. Here are some best practices for pump discharge piping:
1. Use a straight pipe section: Install a straight pipe section of at least five times the pipe diameter before any elbows or fittings on the discharge side of the pump. This helps to reduce turbulence and pressure drop in the system.
2. Support the piping: Properly support the discharge piping to prevent sagging or misalignment, which can cause stress on the pump and reduce its efficiency.
3. Avoid excessive bends: Minimize the number of bends and elbows in the discharge piping to maintain a smooth flow of fluid. Excessive bends can increase friction losses and reduce the pump's performance.
4. Check for leaks: Regularly inspect the discharge piping for any leaks or damage. Leaks can lead to loss of fluid and decrease the pump's effectiveness.
By following these best practices for pump discharge piping, you can ensure the reliable and efficient operation of your centrifugal pump.
Pipe sizing is a balancing act between cost and friction loss. Larger pipes cost more, whereas smaller pipes impose greater friction losses on the system. In terms of diameter, discharge pipe diameter should normally match the discharge flange on the pump
GN designed 3 size of diamter, 12inch, 14inch,18inch, each size has 4 different length for option according to the drilling site of the customer. Screw Conveyor - GN Solids Control Tel: +86-187-0156-0173 E-mail: [email protected] of AIPU Screw Conveyor. Compact design with small foot print. Tightseal. Stable and .
centrifugal pump suction and discharge|centrifugal pump selection chart