centrifugal pump alignment|pump alignment procedure : commercial Prior to the pumps being functionally tested, they should be inspected to ensure that the commissioning works will not be impacted. To allow this a detailed Pump Commissioning … See more The Milwaukee transfer pump's flexible impeller and powerful pump move water at up to 480 Gal. per hour, generates up to 18 ft. of lift and produces up to 75 ft. of head height. As a part of the M18 System, REDLITHIUM battery packs power .
{plog:ftitle_list}
• Prime pump by filling pump and piping through open-ing in top of tee with clean water. See Figure 1. • Install pipe plug in top of tee using Teflon™ tape or equivalent. NOTICE: IF PUMP IS DRAINED OR SHUT OFF DUR - ING PRIMING PERIOD, CASING MUST BE REFILLED BEFORE RESTARTING PUMP. • Start the pump and partially open discharge valve and
Centrifugal pump alignment is a critical process in the installation and maintenance of pumps in various industrial applications. Proper alignment ensures optimal performance, efficiency, and longevity of the pump system. It should be noted that, unless specified and requested within the order to the supplier/manufacturer, pumps are not usually factory tested. Therefore, it is essential for operators and maintenance personnel to understand the importance of pump alignment and follow the correct procedures to achieve accurate alignment.
Pumps come in various configurations and sizes, the below information is based upon the most basic type that we come across, ‘Centrifugal Pumps’, that are used in commercial and industrial chilled water and heating systems. It is assumed that the pump motor megger/insulation testing has been completed
Types of Pump Alignment
There are several types of pump alignment methods commonly used in the industry, including:
1. Parallel Alignment: In parallel alignment, the pump shaft and motor shaft are aligned parallel to each other. This method is suitable for pumps with flexible couplings.
2. Angular Alignment: Angular alignment involves aligning the pump shaft and motor shaft at a specific angle to each other. This method is used for pumps with rigid couplings.
3. Combination Alignment: Combination alignment combines both parallel and angular alignment methods to achieve precise alignment for pumps with complex configurations.
Pump Alignment Definition
Pump alignment refers to the process of ensuring that the pump shaft is properly aligned with the motor shaft to minimize vibration, reduce wear on bearings, and improve overall pump efficiency. Proper alignment is essential for preventing premature failure of pump components and ensuring smooth operation of the pump system.
Pump Alignment Procedure
The pump alignment procedure typically involves the following steps:
1. Verify Equipment: Before starting the alignment process, ensure that the pump, motor, and coupling components are in good condition and free from any defects.
2. Rough Alignment: Initially, perform a rough alignment by aligning the pump and motor shafts visually or using basic alignment tools.
3. Pre-alignment Checks: Check for soft foot conditions, ensure proper coupling fit, and verify that the pump and motor bases are level and securely mounted.
4. Fine Alignment: Use precision alignment tools such as dial indicators or laser alignment devices to achieve accurate alignment within specified tolerances.
5. Verify Alignment: After completing the alignment process, verify the alignment by checking for runout and performing a trial run to ensure smooth operation.
Pump Alignment Method
There are several methods for aligning centrifugal pumps, including:
1. Rim and Face Alignment: This method involves measuring the gap between the pump and motor coupling faces to determine alignment.
2. Reverse Dial Indicator Alignment: Using a dial indicator to measure shaft misalignment and make adjustments to achieve proper alignment.
3. Laser Alignment: Laser alignment systems provide precise measurements of shaft alignment and are commonly used for high-precision alignment tasks.
Pump Shaft Alignment Chart
A pump shaft alignment chart is a visual representation of the alignment tolerances and specifications for centrifugal pumps. The chart typically includes allowable misalignment values for parallel and angular alignment, as well as guidelines for achieving proper alignment.
How to Check Pump Alignment
To check pump alignment, follow these steps:
1. Use a dial indicator or laser alignment tool to measure the alignment of the pump and motor shafts.
2. Check for runout and excessive vibration during operation, which may indicate misalignment.
3. Monitor bearing temperatures and noise levels, as improper alignment can lead to increased wear and premature failure of bearings.
Pump Alignment Standard
The pump alignment standard refers to the industry-accepted guidelines and tolerances for aligning centrifugal pumps. These standards outline the maximum allowable misalignment values for parallel and angular alignment to ensure optimal pump performance and reliability.
Pump Alignment with Dial Indicator
It should be noted that, unless specified and requested within the order to the supplier/manufacturer, pumps are not usually factory tested. See more
Cavitation occurs in centrifugal pumps when the Nett Positive Suction Head Available is lower than the Nett Positive Suction Head Required.
centrifugal pump alignment|pump alignment procedure